Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Liner & Rebuild in Paterson: What to Know First
Olympia Chimney liner and rebuild work in Paterson typically runs between $2,400 and $7,800 depending on whether you need a stainless steel liner replacement, a partial rebuild, or a full teardown. Most jobs take one to two days on site, and we give you a written price before anything starts, every time. Corrine Halstead and our crew at Level Two Chimney Paterson have been working on Olympia Chimney systems across Passaic County for years, including older row houses near the Great Falls Historic District where the flues are original and the conditions are rarely simple.
If you own a home in Paterson with an Olympia Chimney liner or chimney system and you suspect it’s failing, this page covers what actually goes wrong, what it costs to fix here, and how we approach the work. Call (862) 356-5229 for a free estimate. We’re an independent Olympia Chimney service provider, not a manufacturer affiliate, which matters for your warranty and your wallet.
Key Takeaways
- Olympia Chimney liner and rebuild work in Paterson costs $2,400 to $7,800 depending on scope.
- Most jobs are done in one to two days, with a written price, written scope, and written warranty before we start.
- We document everything with a camera scan and photo record on every visit, per Haven Standard Clause 4.
- We service all Olympia Chimney product lines and stock quality aftermarket parts from DuraFlex, HeatShield, Gelco, and Copperfield.
- Free second opinions on any written competitor estimate.
How Olympia Chimney Products Fail - and How We Fix Them
Olympia Chimney builds solid stainless steel liner systems, but in Paterson’s climate - freeze-thaw cycles, humidity off the Passaic, and decades of coal-to-gas-to-oil fuel transitions in older homes - we see specific patterns. Here’s what actually fails and what we do about it:
- Olympia Chimney 316L flexible liners - pitting at the corbel bend. In Paterson row houses and older colonials, the flue often takes a hard offset where it passes through the smoke shelf or around a corbeled masonry bump. We see pitting and micro-perforation right at that bend, usually within 12 to 15 years of install. The fix is a measured replacement section or full liner swap, never a patch, because the pitting pattern repeats within a few feet. We document the corrosion zone with camera footage so you can see exactly where the metal is thinning.
- Olympia Chimney rigid stainless sections - failed slip joints at the flue collar. On some older Olympia Chimney rigid systems, the slip joints that connect liner sections to the appliance flue collar loosen over time. When that happens, flue gases bypass the liner at the joint, and you lose draft on startup. We see this more in Paterson homes that converted from oil to gas in the 1990s and early 2000s without reconfiguring the flue collar properly. The fix is a collar re-seat with fresh gasketing and, when needed, a transition to a smooth-wall liner from our DuraFlex or Copperfield inventory.
- Olympia Chimney caps - mesh clogging with poplar and maple seed. Paterson’s street trees drop fine seed material in May and June, and it collects on the cap mesh until it blocks airflow. An Olympia Chimney cap with a standard mesh spacing clogs faster than aftermarket caps with wider spacing. We swap in a cap from our Gelco or Famco stock when we do a rebuild, and we show you the before and after airflow readings.
- Olympia Chimney tee-snout assemblies - creosote damning in the lower half. This is a real pattern in Paterson because many homes here are still burning utility wood in the shoulder seasons. The tee-snout at the base of the liner collects Class III creosote (the shiny, hardened tar) when fires run cool. That creosote is flammable at temperatures a normal flue reaches. We remove the tee-snout, clean it properly, and if the creosote has already damaged the seam, we replace it with a fresh Olympia Chimney part or a HeatShield-certified equivalent.
- Olympia Chimney masonry surround failures - the liner is fine, the brick is not. Sometimes the liner is intact and the problem is the chimney stack itself: spalling brick face, failed mortar joints, or a cracked crown. In Paterson’s freeze-thaw cycle, water gets into the masonry, freezes, expands, and pops the brick face off in sheets. We do partial rebuilds and full chimney rebuilds as needed and always inspect the existing liner during that work. If the liner is sound, we keep it. If it isn’t, the rebuild is the right time to reline because the scaffold is already up and the labor overlap saves money.
Our Olympia Chimney Chimney Liner & Rebuild Process
Camera first, quote second, work third - in that order, every time. Here’s what a typical Olympia Chimney liner and rebuild job looks like when you call us in Paterson:
- 1
Call and schedule. You reach a live person at (862) 356-5229, 24/7. We take your address, ask a few questions about when the system was installed and what you’ve been noticing, and book a visit that works for you. Your tech is named and background-checked, and you get a text when they’re on the way.
- 2
NFPA 211 Level 2 camera inspection. We run a camera down the entire flue and record everything. You watch the footage with us on screen. We note the liner condition, joint integrity, creosote class, crown condition, and any gaps or bypasses. This is the same inspection standard we’ve run since 2009, and it’s included on every visit.
- 3
Written scope and price. You get a written document that says exactly what we found, what we propose to do, what parts we plan to use (Olympia Chimney OEM or quality aftermarket from DuraFlex, HeatShield, Gelco, Famco, or Copperfield), and what the work will cost. No verbal estimates, no change orders without written sign-off. This is Haven Standard Clause 1, and we’ve never done it differently.
- 4
Liner replacement or rebuild. If we’re relining, we remove the old liner, prep the flue, and install the new stainless steel system with proper insulation where the clearances require it. If we’re rebuilding, we tear out the damaged masonry, rebuild with matching brick, and pour a new crown with a proper drip edge. Every step gets photographed.
- 5
Test and verify. We run draft and pressure checks, fire the system if it’s operable, and confirm the liner is seated correctly with final camera footage. You get a documented photo record of the entire job on completion, another Haven Standard Clause 4 promise.
- 6
Cleanup and warranty. We leave the site cleaner than we found it, leave your written warranty in hand, and walk you through the 365-Day Done Right Promise: if it’s not done right, we make it right. A year of coverage, no fine print.
BeforeAfterWhat Olympia Chimney Chimney Liner & Rebuild Costs in Paterson
Honest numbers for Paterson homeowners, based on what we’ve actually quoted and built:
- Stainless steel liner replacement (Olympia Chimney 316L flexible, single story): $2,400 to $3,800
- Liner replacement with tee-snout and cap (two-story or offset flue): $3,400 to $5,200
- Partial chimney rebuild (top 3 to 5 courses, crown, cap, liner re-seat): $4,800 to $7,000
- Full chimney rebuild from the roof line up: $6,500 to $12,000 plus, depending on access, height, and brick match
- Liner repair (section replacement or joint re-seal, where safe): $800 to $1,800
The price moves based on three things in Paterson: the height and access of your chimney (three-story row houses near the Great Falls cost more to scaffold than a one-story ranch in Weasel Park), whether the existing flue requires resizing for gas or oil, and the condition of the surrounding masonry. Every estimate is written and free. Call (862) 356-5229 for a specific number on your chimney.
Why Paterson Homeowners Call Level Two Chimney Paterson for Olympia Chimney Work
Most of our Paterson customers have never heard of us before they call. They usually have an Olympia Chimney liner that’s failed, or a chimney stack that’s spalling, and they want to know two things: what it costs and whether the person quoting it actually knows the system they’re quoting. We answer both directly. Our techs work on Olympia Chimney products every week, and when a part isn’t available or a more durable option exists, we say so plainly and quote quality aftermarket alternatives from DuraFlex, HeatShield, and Gelco. We don’t pretend to be an Olympia Chimney dealer. We’re an independent service provider, and that independence means we recommend the right part for your chimney, not the one a manufacturer’s program pushes.
Every job includes a documented photo record. Every quote is written before work starts. Every customer is backed by the 365-Day Done Right Promise. And if someone else quoted you in writing, we’ll give you a free second opinion on that estimate. Corrine Halstead started working on Paterson chimneys years ago and her rule has not changed: look first, write it down, then quote. If you want someone to show you the problem on camera before asking for a dollar, call (862) 356-5229.
FAQs
Olympia Chimney warranties typically cover manufacturing defects in the liner material itself, not labor, installation, or damage from creosote corrosion, chimney fire, or water entry. In Paterson, where freeze-thaw and moisture intrusion cause most failures, the warranty usually does not apply. We document the cause of failure with camera footage so you know what you’re looking at and can make an informed decision about repair versus replacement. If you have a written warranty question, bring it up when you call (862) 356-5229; we’ll walk you through what’s covered and what isn’t, and quote you honestly either way.
Depends on where the damage is and what caused it. Small joint gaps and collar leaks are repairable with section replacement or re-seating, and we do those jobs for $800 to $1,800 in Paterson. Pitting along a corbel bend or creosote-thinned metal usually means the liner needs to be replaced entirely because the wall thickness is compromised beyond a safe margin. We will always show you the camera footage and explain why repair is or isn’t safe before we quote a replacement. Call (862) 356-5229 and we’ll assess yours on site.
OEM Olympia Chimney liner sections and components usually arrive in three to five business days from our suppliers. If you need the system functional sooner, we stock aftermarket equivalents from DuraFlex, HeatShield, and Copperfield that are often available same-week and meet or exceed the original specs. We’ll tell you the lead time for each option when we write the quote. For emergency situations in Paterson, call (862) 356-5229 and we’ll tell you what’s available immediately.
Not necessarily. If the liner failed but the masonry is sound - solid bricks, good mortar, no spalling, and a functioning crown - you only need a liner replacement. If the masonry is compromised and we’re already removing and rebuilding a section, doing the liner at the same time saves on scaffold and labor because the flue is already accessible. We will quote you separately for each scope so you can see exactly what each choice costs, and you decide. A free estimate from (862) 356-5229 includes both numbers when both apply.
Bring us the written estimate. We offer a free second opinion on any competitor’s written quote, which means we’ll inspect your chimney, review their scope, and tell you honestly whether their price matches the work they’re proposing. We’re not trying to be the cheapest in Paterson; we’re trying to be the most accurate. If the other quote is fair, we’ll tell you. If it’s inflated or missing something critical, we’ll tell you that, too. Call (862) 356-5229 with the estimate in hand.
Written by Corrine Halstead, Owner, Level Two Chimney Paterson at Level Two Chimney Paterson, serving Paterson and nearby areas.